Pedal Type: All-Analog Full-Stereo Flanger
Controls: Speed Knob, Width Knob, Sweep Knob, Feedback Knob, Dimension Toggle Switch, Bypass Footswitch
Bypass Layout: Buffered Bypass
Power Requirements: 9VDC Center-Negative External Power Supply Only
Current Draw: 250mA
Dimensions: 4.9 x 3.2 x 3.2 inches / 125 x 80 x 80 mm
The internal circuitry of this performance-grade modulation engine is constructed around a matched network of four genuine MN3009 Bucket Brigade Device IC chips. Operating strictly within the analog domain, this hardware setup provides a 2.2M ohm input impedance to maintain absolute signal purity when driven by hot passive pickups or active electronic systems. By managing voltage distribution across four distinct analog delay paths, the architecture achieves massive dynamic headroom, preventing early internal clipping or harsh digital distortion. The physical solid-state bucket brigade topology introduces a natural high-frequency roll-off and warm harmonic integration, capturing the sweeping depth and low-noise floor of classic analog studio processors.
The control interface facilitates meticulous parameter manipulation to redefine traditional comb-filtering boundaries. While the Speed and Width controls dictate the primary LFO rate and sweeping amplitude, the Sweep control introduces independent, bi-directional time-shifting across the stereo field. Turning the Sweep knob adjusts the delay time on one channel while inversely moving the time threshold on the adjacent channel. This works directly with a bi-directional Feedback control, which dials in positive resonance when turned clockwise and negative resonance when turned counter-clockwise from the center zero position. Activating the onboard Dimension mini-toggle crossfeeds the dual channels into one another, modulating both delay lines in opposite directions simultaneously to unlock an organic double-flanger matrix.
For complex live topologies or tracking environments that demand a wide, non-overlapping stereo field, this stompbox maximizes spatial processing without frequency cancellation. Interface your main instrument into the primary input, then route independent quarter-inch cables from the stereo outputs into separate clean guitar amplifiers. Set the Speed control to 10:00, advance the Width to 3:00, and position the Sweep control past 2:00 to heavily split the channel delay offsets. Adjust the Feedback control clockwise to introduce sharp positive resonance. This configuration generates an expansive, sweeping stereo architecture where the phase-shifted combat paths swirl between both enclosures cleanly, retaining a tight, punchy low-end response.
To construct an intense, dramatic jet-stream modulation pattern for hard rock leads or saturated chordal tracking, position the unit directly after your gain-stacking elements or distortion circuits. Keep the Dimension switch engaged to activate the dual-modulating delay paths, set the Speed to 9:00, and turn the Width control to 12:00. Carefully sweep the Feedback control counter-clockwise to tap into the hollow, woody characteristics of negative resonance. The robust internal analog buffers accept the compressed, harmonic-rich clipping of your distortion pedals smoothly, creating an interactive, voice-like sweeping filter texture that carves a distinct path through dense rhythm tracks.
IMPORTANT ELECTRICAL AND OPERATIONAL WARNINGS: REGULATED 9VDC CENTER-NEGATIVE DC POWER SUPPLY REQUIRED FOR OPERATION. DO NOT ATTEMPT TO POWER THIS EFFECТ PEDAL WITH AC VOLTAGE OR ANY DIRECT CURRENT SOURCE EXCEEDING 9VDC. THE APPLICATION OF UNAUTHORIZED VOLTAGES WILL VOID THE MANUFACTURER WARRANTY AND CAUSE IRREVERSIBLE DESTRUCTION TO THE FOUR INTEGRATED MN3009 BUCKET BRIGADE CHIPS. THIS UNIT IS ENTIRELY DEPENDENT ON AN EXTERNAL POWER SOURCE AND DOES NOT ACCEPT INTERNAL 9V BATTERIES. POWER SUPERSATURATION AND IMPROPER GROUNDING CAN PROVOKE CIRCUIT DAMAGE. WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING LEAD, WHICH ARE KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM. KEEP INSTRUMENT INTERFACES CLEAN AND DRY. DO NOT OPERATE IN CONDENSING HUMIDITY.
Pedal Type: All-Analog Full-Stereo Flanger
Controls: Speed Knob, Width Knob, Sweep Knob, Feedback Knob, Dimension Toggle Switch, Bypass Footswitch
Bypass Layout: Buffered Bypass
Power Requirements: 9VDC Center-Negative External Power Supply Only
Current Draw: 250mA
Dimensions: 4.9 x 3.2 x 3.2 inches / 125 x 80 x 80 mm
The internal circuitry of this performance-grade modulation engine is constructed around a matched network of four genuine MN3009 Bucket Brigade Device IC chips. Operating strictly within the analog domain, this hardware setup provides a 2.2M ohm input impedance to maintain absolute signal purity when driven by hot passive pickups or active electronic systems. By managing voltage distribution across four distinct analog delay paths, the architecture achieves massive dynamic headroom, preventing early internal clipping or harsh digital distortion. The physical solid-state bucket brigade topology introduces a natural high-frequency roll-off and warm harmonic integration, capturing the sweeping depth and low-noise floor of classic analog studio processors.
The control interface facilitates meticulous parameter manipulation to redefine traditional comb-filtering boundaries. While the Speed and Width controls dictate the primary LFO rate and sweeping amplitude, the Sweep control introduces independent, bi-directional time-shifting across the stereo field. Turning the Sweep knob adjusts the delay time on one channel while inversely moving the time threshold on the adjacent channel. This works directly with a bi-directional Feedback control, which dials in positive resonance when turned clockwise and negative resonance when turned counter-clockwise from the center zero position. Activating the onboard Dimension mini-toggle crossfeeds the dual channels into one another, modulating both delay lines in opposite directions simultaneously to unlock an organic double-flanger matrix.
For complex live topologies or tracking environments that demand a wide, non-overlapping stereo field, this stompbox maximizes spatial processing without frequency cancellation. Interface your main instrument into the primary input, then route independent quarter-inch cables from the stereo outputs into separate clean guitar amplifiers. Set the Speed control to 10:00, advance the Width to 3:00, and position the Sweep control past 2:00 to heavily split the channel delay offsets. Adjust the Feedback control clockwise to introduce sharp positive resonance. This configuration generates an expansive, sweeping stereo architecture where the phase-shifted combat paths swirl between both enclosures cleanly, retaining a tight, punchy low-end response.
To construct an intense, dramatic jet-stream modulation pattern for hard rock leads or saturated chordal tracking, position the unit directly after your gain-stacking elements or distortion circuits. Keep the Dimension switch engaged to activate the dual-modulating delay paths, set the Speed to 9:00, and turn the Width control to 12:00. Carefully sweep the Feedback control counter-clockwise to tap into the hollow, woody characteristics of negative resonance. The robust internal analog buffers accept the compressed, harmonic-rich clipping of your distortion pedals smoothly, creating an interactive, voice-like sweeping filter texture that carves a distinct path through dense rhythm tracks.
IMPORTANT ELECTRICAL AND OPERATIONAL WARNINGS: REGULATED 9VDC CENTER-NEGATIVE DC POWER SUPPLY REQUIRED FOR OPERATION. DO NOT ATTEMPT TO POWER THIS EFFECТ PEDAL WITH AC VOLTAGE OR ANY DIRECT CURRENT SOURCE EXCEEDING 9VDC. THE APPLICATION OF UNAUTHORIZED VOLTAGES WILL VOID THE MANUFACTURER WARRANTY AND CAUSE IRREVERSIBLE DESTRUCTION TO THE FOUR INTEGRATED MN3009 BUCKET BRIGADE CHIPS. THIS UNIT IS ENTIRELY DEPENDENT ON AN EXTERNAL POWER SOURCE AND DOES NOT ACCEPT INTERNAL 9V BATTERIES. POWER SUPERSATURATION AND IMPROPER GROUNDING CAN PROVOKE CIRCUIT DAMAGE. WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING LEAD, WHICH ARE KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM. KEEP INSTRUMENT INTERFACES CLEAN AND DRY. DO NOT OPERATE IN CONDENSING HUMIDITY.
